website@flyteccomputers.com

Digium

Part:
1TE236F

Digium 1TE236F TE236 Dual-Port T1/E1/J1/PRI PCI Telephony Card, 3.3/5 V, Without Hardware Echo Cancellation

$575.90
$699.00
Condition:
New

PRODUCT SPECIFICATIONS

Digium 1TE236F TE236 Dual-Port Digital PCI Telephony Card

The Digium 1TE236F is a dual-port digital telephony card for connecting T1, E1 or J1 circuits to a compatible host server. Used with Asterisk and DAHDI, it provides an interface between digital telephone trunks and software-based business communications systems.

The TE236 installs in a conventional PCI slot supporting 3.3 V or 5 V signaling. Its low-profile, half-length design supports integration into suitable server chassis. This configuration does not include a hardware echo cancellation module.

Key Features

  • Two digital T1/E1/J1 interfaces.
  • Support for Primary Rate ISDN and other documented digital signaling modes.
  • Conventional PCI 2.2 or later host interface.
  • Universal 3.3 V/5 V PCI signaling compatibility.
  • Low-profile, half-length card design.
  • Integration with Asterisk through DAHDI.
  • Optional VPM064 hardware echo cancellation module.

Digital Trunk Integration

Connect compatible carrier circuits, digital PBX interfaces or channel banks through the two telephony ports. Match the line mode, framing, coding, signaling and clock source to the connected equipment or service.

Channel Capacity

Two T1 spans can provide up to 48 voice channels with suitable channel-associated signaling. Two conventional T1 PRI spans normally provide 46 bearer channels because each span reserves one channel for signaling. Two E1 PRI spans normally provide 60 bearer channels. Available capacity depends on circuit provisioning and configuration.

Asterisk and DAHDI

The card supplies digital telephony connectivity to the host system. PBX functions, IP calling and call routing are provided by the installed software. .

Echo Cancellation

The 1TE236F does not include hardware echo cancellation. Software echo cancellation may be configured in the host system, or a compatible VPM064 module may be added separately.

Ideal Applications

  • Connecting digital telephone trunks to an Asterisk PBX.
  • Integrating legacy PBX equipment with a software-based phone system.
  • Building a host-based digital-to-VoIP gateway.
  • Maintaining compatible PCI-based telephony servers.

Compatible Products

Host requirements: Use a compatible conventional PCI 2.2-or-later slot with 3.3 V or 5 V signaling and sufficient chassis clearance. Verify the installed bracket matches the chassis opening.

Digital line requirements: The connected circuit or equipment must match the configured T1/E1/J1 mode, framing, line coding, signaling role and clock source.

Important: The TE236 does not fit a PCI Express slot. Its modular telephony ports are not Ethernet LAN ports and must not be connected to an Ethernet switch or PoE injector. Analog telephones and analog PSTN lines require appropriate intermediary equipment.

Technical Specifications

General

  • Brand: Digium
  • Model: TE236
  • MPN: 1TE236F
  • Product Type: Dual-span digital telephony interface card
  • Form Factor: Low-profile, half-length

Host Interface

  • Bus: Conventional PCI, version 2.2 or later
  • Bus Width / Clock: 32-bit, 33 MHz
  • PCI Signaling: Universal 3.3 V/5 V
  • PCI Express: Not supported

Digital Telephony

  • Ports: 2 x RJ48C digital telephony interfaces
  • Line Modes: T1, E1 and J1
  • Signaling: PRI, CAS/robbed-bit signaling, CCS and E&M, subject to configuration
  • PRI Roles: Network and CPE
  • Line Coding: AMI, B8ZS and HDB3, as applicable
  • Hardware Echo Cancellation: Not included
  • Optional Echo Module: VPM064

Software

  • Telephony Platform: Asterisk
  • Hardware Interface: DAHDI
  • Driver: wcte43x

Power

  • Power Source: Host PCI bus
  • Published Maximum Consumption: 4 W for TE236, according to the TE230 Series manual
  • PoE: Not applicable

Physical and Environmental

  • PCB Dimensions, Manual: 127 x 69 x 15 mm, excluding PCI bracket
  • Weight: Approximately 100 g without echo cancellation module
  • Operating Temperature: 0°C to 50°C
  • Storage Temperature: -20°C to 65°C
  • Humidity: 10–90%, non-condensing

Download Digium TE236 1TE236F Specifications — Telephony Cards Datasheet (PDF)

More Information

MFRPartNum:
1TE236F
Datasheet: