PRODUCT SPECIFICATIONS
L-com ANM-1406 N-Male Straight Crimp Connector for RG8/LMR-400 Cable
The L-com ANM-1406 is a straight, cable-mounted N-male RF connector for terminating compatible RG8, LMR-400 and 400-series low-loss coaxial cable. Its 50-ohm impedance and DC–6 GHz frequency range suit a variety of antenna-feed, WLAN and general RF cable applications.
The connector uses crimp termination for the center contact and outer ferrule. A nickel-plated brass body, gold-plated brass center contact and PTFE insulator provide the documented material construction. Proper installation requires compatible cable, accurate cable preparation and the specified crimp sizes.
Key Features
- Standard-polarity Type N male plug with male center contact.
- Straight cable-mount design.
- 50-ohm impedance.
- DC–6 GHz operating frequency range.
- Designed for RG8/LMR-400 and compatible 400-series low-loss coaxial cable.
- Crimp termination for the center contact and ferrule.
- Nickel-plated brass body and gold-plated brass center contact.
- PTFE insulation.
- Documented VSWR below 1.50:1 across DC–6 GHz.
RF Performance
The ANM-1406 provides a 50-ohm RF connection within its specified frequency range. Performance of the completed cable assembly also depends on cable attenuation, cable length, preparation quality, crimp quality and the mating interface.
This passive connector does not amplify signals or determine a wireless link's data rate. Select every component of the RF path for the intended frequency and application.
Cable Termination and Installation
Use the manufacturer drawing to prepare the cable and position the center contact, connector body and ferrule. The drawing specifies a 0.100-inch center-contact crimp and a 0.429-inch ferrule crimp.
Confirm the exact cable construction before assembly. Similar outside diameter alone does not establish compatibility with the cable's center conductor, dielectric or shield.
Materials and Construction
The connector includes nickel-plated brass body components and ferrule, a gold-plated brass center contact, a PTFE insulator and an MVQ gasket. The threaded N-male interface mates with an appropriate standard-polarity N-female RF interface.
Ideal Applications
- Building compatible 50-ohm coaxial cable assemblies.
- Terminating RG8, LMR-400 and approved 400-series antenna-feed cables.
- Replacing damaged connectors on compatible coaxial cable.
- WLAN and antenna installations operating within DC–6 GHz.
- General RF interconnections using standard N-type interfaces.
Compatible Products
The ANM-1406 requires compatible 50-ohm coaxial cable whose center conductor, dielectric, shield and jacket dimensions match the connector's termination design. Follow the manufacturer drawing and specified crimp sizes.
- L-com CA-400-R1K CA-400 Coaxial Cable, 1,000-Foot Reel – CA-400 is explicitly listed as a supported cable type in Flytec's ANM-1406 description. The reel supplies bulk cable for preparing and crimping custom assemblies.
Important: RG8, RG8X and RG400 are different cable designations. Do not assume this connector fits RG8X or RG400. Likewise, 195-series, 240-series and 600-series cables require connectors designed for their dimensions.
Mating interface: This is a standard-polarity N-male connector. Do not confuse it with reverse-polarity N connectors, N-female connectors, SMA or RP-SMA interfaces.
Outdoor installation: An installed gasket does not establish a verified IP rating for the completed cable assembly. Confirm the weather-sealing requirements of the installation.
Technical Specifications
General
- Brand: L-com
- Model / MPN: ANM-1406
- Product Type: RF coaxial cable connector
- Connector Series: Type N
- Gender: Male plug with male center contact
- Polarity: Standard
- Orientation: Straight
- Mounting: Cable mount
- Coupling: Threaded
Electrical and RF
- Impedance: 50 ohms
- Frequency Range: DC–6 GHz
- VSWR: Less than 1.50:1 over DC–6 GHz
- Withstand Voltage: 2500 V; not a continuous operating-voltage specification
Cable Termination
- Drawing-Identified Cable Types: RG8 / LMR-400
- Catalog Cable Family: Compatible low-loss 400-series coaxial cable
- Center Contact Termination: Crimp
- Shield / Ferrule Termination: Crimp
- Recommended Center-Contact Crimp Size: 0.100 inch, shown as 2.5 mm
- Recommended Ferrule Crimp Size: 0.429 inch, shown as 10.9 mm
Materials
- Body: Nickel-plated brass
- Outer Contact: Nickel-plated brass
- Center Contact: Gold-plated brass
- Crimp Ferrule: Nickel-plated brass
- Insulator: PTFE
- Gasket: MVQ
- Retaining Ring: Phosphor bronze
Mechanical Specifications
- Connector Body Length: 22.10 mm (0.87 inch)
- Separate Ferrule Length: 20 mm (0.79 inch)
- Coupling Thread: 5/8-24 UNEF-2B
- Durability: Greater than 500 mating cycles
- Cable Retention: Greater than 40 lbf
Environmental and Compliance
- RoHS: Manufacturer drawing references Directive 2011/65/EU
Download L-com ANM-1406 N-Male Crimp Connector Drawing and Specifications (PDF)