Ubiquiti UA-G2-PRO Unifi Access G2 Reader Pro NFC Reader UniFi Identity mobile app intercom (Black)

Technical Description

• Mechanical
  • Dimensions: 160 x 40.4 x 40.55 mm (6.3 x 1.59 x 1.6')
  • Weight: 136 g (4.8 oz)
  • Enclosure material: Polycarbonate, glass
  • Mount material: Aluminum alloy
  • Mounting: Wall, gang box
  • Weatherproofing: IP55
• Hardware
  • Networking interface: (1) GbE RJ45 port
  • Connectivity: 
    • BLE 4.2
    • NFC
  • Power method: 
    • PoE
    • UL 294 Power-limited Class 2 PSU
    • UL 60950-1/62368-1 LPS/PS2 PSU
  • Supported voltage range: 48V DC
  • Max. power consumption: 6W
  • ESD/EMP protection: Air: ±15kV, contact: ±8kV
  • Sensor: Proximity sensor
  • Camera: 4000 x 3000, 12 MP, 30 FPS
  • Microphone: Yes
  • Speaker: (1) 4 ohm, 1.5W
  • LEDs: 
    • R/G/B/W
    • Flash
  • Button: (1) Factory-reset
  • NFC frequency: 13.56 MHz
  • NFC read range: < 30 mm
  • NFC standards: ISO 14443A, 14443B, 15693
  • NFC technology: 
    • NFC Tag 1,2,3,4,5
    • MIFARE Classic
    • MIFAREPlus
    • MIFARE Ultralight
    • MIFARE DESFire
  • Operating environment: Outdoor use
  • Ambient operating temperature: 
    • Device: -30 to 45° C (-22 to 113° F)
    • Display:* -10 to 45° C (14 to 113° F) (*The display will turn off when the ambient temperature is above/below the display operation temperature, but other functions will remain functional.) (Effective after firmware v1.3.28)
  • Ambient operating humidity: 5 to 90% non-condensing
  • Software information: The software version of a product can be checked at https://unifi.ui.com
  • UL 294 level: 
    • Destructive attack: Level I
    • Line security: Level I
    • Endurance: Level I
    • Standby power: Level I
  • UL 294 statement
    • Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
    • The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
  • PoE cabling requirements:
    • Cable 5e cabling is the minimum performance category recommended. The performance category utilized should match the transmission speed required at the installation site.
    • The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm2) for patch cords; 24 AWG (0.21 mm2) for horizontal or riser cable.
  • CAN/ULC-60839-11-1 Grade: Grade assignment: I
  • Certifications: CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
  • Document number, and issue date and/or revision level: UA-G2-Pro/UA-G2-Pro-Black, V02
• LED
  • System: 
    • Steady blue: Adopted/device is ready
    • Steady white: Pending adoption
    • Blinking white/blue: Upgrading firmware
    • Strobing red: Emergency lockdown
• Software
  • Management application: UniFi Access: Version 1.5.9 and later