Tycon Power Systems


Tycon EZ-Bridge-LT2+ high power outdoor 2.4GHz wireless PtP bridge system



The EZ-Bridge LT2+ is a high power 25dBm (316mW) outdoor wireless bridge system operating in the 2.4GHz unlicensed frequency spectrum providing real world throughput up to 100 Mb/sec. It complies with the 802.11gn standards to insure interoperability. The EZ-Bridge LT2+ creates a transparent wireless bridge between two networks up to 3 miles apart with good line of sight.

It supports VOIP, VPN, multiple MAC addresses and DHCP across the wireless link.

It is the perfect plug and play solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access.

Multiple EZ-Bridge LT2+ units can be connected in a mesh configuration to allow interconnecting more than two sites.
With its password verification, MAC address authentication, SSID suppression and advanced WPA encryption, the system provides the best available wireless data security.

Installation is a snap because of the plug and play features which have been built into the system. Just install the antennas and plug in the power inserters. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.

The EZ-Bridge LT2+ comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi 802.11gn MIMO antennas with built-in high power electronics, Bracket Kits which accommodate pole or wall mounting and Cat5e rated 24V POE (Power Over Ethernet) power inserters. Customer needs to supply CAT5 cabling between the power inserter and the antenna and between the power inserter and his computer, router or switch.


  • High Power Electronics and powerful antenna
  • True Plug and Play
  • 64 and 128bit WEP, WPA and WPA2 Encryption 
  • Web-based configuration
  • Power over Ethernet
  • Layer 2 Transparent Bridge


  • Operation up to 3 miles with good line of sight and up to 100 Mbps real world throughput
  • No driver needed. Pre-configured at the factory for automatic peer to peer communications
  • Most powerful data security available
  • Remotely change device configuration or update firmware from anywhere on the network
  • Antennas can be mounted up to 100meter (300’) from the power inserter
  • Appears to network devices as if an Ethernet cable has been installed between the 2 network nodes. Passes DHCP, VOIP Packets, VLAN Packets and supports multiple MAC addresses

Complete System Weight

  • 3 kg (7 lbs)

Technical Description

  • Data Rates: 2.4Ghz 802.11n: up to 300Mbps ; 2.4 GHz 802.11g: up to 54Mbps ; 5GHz 802.11n: up to 300Mbps ; 5GHz 802.11a: up to 54Mbps
  • Standards: IEEE802.11g/n, 802.11a/n, 802.3, 802.3u
  • Power Requirements: Power Supply: 100-240VAC 50/60Hz ; EZ-Bridge® : 12VDC to 24VDC Passive PoE ; Average Power Consumption: 4W
  • Regulatory Certifications: FCC Part 15 / UL
  • RF Frequency Band: 2400 ~ 2497 MHz ; 5100 ~ 5850 MHz
  • Modulation Technology: 802.11n: TDMA ; 802.11g: OFDM ; 802.11a: OFDM
  • Receive Sensitivity (Typical): 802.11n: -90 dBm ; 802.11g: -75 dBm ; 802.11a: -75 dBm
  • Transmit Power: 25dBm 316mW
  • DC Connector Power Out: Input Voltage @ Max 10W
  • Antenna: 2.4GHz 14dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back ; 5GHz 16dBi MIMO Panel Antenna, 27deg Beamwidth, >22dB front to back
  • Operation Mode: – Bridge or Router Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
  • Interface: 10/100Mbps RJ-45 LAN Port x 2
  • IP Configuration: Static or Auto configuration using DHCP Client
  • Security MAC Address: Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
  • Management Configuration: Web-based configuration (HTTP) ; Console configuration (SSH) ; SNMP Protocol
  • Firmware Upgrade: Upgrade firmware via web browser
  • Antenna Physical Dimensions (L x W x D): 314mm x 187mm x 65mm (12.4” x 7.3” x 2.5”)
  • Operating Temperature> -30°C to +70°C (-22°F to 158°F)

More Information