null

Our office will be closed on Monday, May 27th in Observance of Memorial Day

Tycon Power Systems

Part:
EZ2+V3

Tycon Replacement board for EZ-Bridge LT2+. 2.4GHz. 100Mbps. 802.11g/n. 250mW

$61.75
$65.00
Condition:
New

PRODUCT SPECIFICATIONS

The EZ2+ is a high performance radio board with 250mW output power and 100Mbps thruput.It conforms to the 802.11b/g/n standards for interoperability with other WLAN systems on the market. It uses the advanced EZOS Linux based operating system for superior performance and stability. It can be configured as an Access Point or Client in Bridge or Router modes. It can also be configured for point to point operations. It also supports a wireless repeater function. The EZ2+ supports wireless security standards WEP and WPA.It gets its power from the CAT5 network cable and requires 12VDC to 24VDC. The antenna connector is a U.FL (IPX) type.

Note: Installation instructions included. Please specify Side A (139, AP) or Side B (239, Client) when ordering. You can specify by replying to the order confirmation email and stating which side you are replacing. If no note is included, board will be sent as Side B (.239, Client) by default.

FEATURES

  • High Power MIMO Compatible Electronics
  • Easy and Straightforward User Interface
  • 64 and 128bit WEP, WPA and WPA2 Encryption
  • Web-based configuration
  • Power over Ethernet 
  • Transparent Bridge (WDS) mode

BENEFITS

  • Operation up to 12 miles or more with good line of sight and a 24dBi antenna
  • No driver needed. Web Interface through any browser
  • Most powerful data security available
  • Remotely change device configuration or update firmware from anywhere on the network
  • Radio boards can be mounted up to 100meter (300’) from the power source
  • Appears to network devices as if an Ethernet cable has been installed between the 2 network nodes. Passes DHCP, VPN and supports multiple MAC addresses

Board Physical Dimensions (L x W x H)

  • 152mm x 104mm x 19mm (4.6” x 4.1” x 0.75”)

Complete System Weight

  • 70g (2.5oz)

Technical Description

  • Data Rates 2.4Ghz 802.11n: up to 300Mbps / 2.4 GHz 802.11g: up to 54Mbps
  • Standards IEEE802.11g/n, 802.3, 802.3u
  • Power Requirements 12VDC to 24VDC Passive PoE or via DC Connector. Average Power Consumption: 4W
  • Regulatory Certifications FCC Part 15 / UL
  • RF Frequency Band 2400 ~ 2497 MHz
  • Modulation Technology 802.11n: TDMA / 802.11g: OFDM
  • Receive Sensitivity (Typical) 802.11n: -90 dBm / 802.11g: -75 dBm
  • Transmit Power 25dBm 316mW
  • DC Connector Power Out 2.1mm x 5.5mm DC Barrel Connector. Output Voltage = PoE Input Voltage @ Max 10W 
  • Reset Button Function 15 seconds – Reset to last saved configuration / 45 seconds – Reset to factory defaults
  • Antenna Connector IPEX, U.FL Qty 2
  • Operation Mode – Bridge or Router Point to Point Bridge, Access Point, Access Point / WDS, Client, Client WDS
  • Interface 10/100Mbps RJ-45 LAN Port x 2. Either port accepts passive PoE input. No PoE output, only data. Can power a second device via the DC Connector.
  • IP Configuration Static or Auto configuration using DHCP Client 
  • Security MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
  • Management Configuration Web-based configuration (HTTP) Console configuration (SSH) SNMP Protocol
  • Firmware Upgrade Upgrade firmware via web browser
  • Operating Temperature -30°C to +70°C (-22°F to 158°F)

More Information

MFRPartNum:
EZ2+V3
Datasheet: