PRODUCT SPECIFICATIONS
Tycon EZGO-DUAL-AC+
The EZ-GO® Dual AC+ is a dual radio, high power 27dBm (500mW), outdoor Access Point or Client/Station operating in the 2.4GHz and 5GHz
unlicensed frequency spectrum providing 5GHz throughput up to 900 Mb/sec.
It complies with the 802.11a/b/g/n/ac standards to insure interoperability. The EZ-GO® Dual AC+ is extremely flexible. It can be used to supply a 5GHz and a 2.4GHz Access Point at the same time or you can use the 5GHz channel to connect to an existing wireless AP and use the 2.4GHz channel to supply a WiFi signal at a remote location. It can be configured as a bridge (default) or Router.
Multiple EZ-GO® Dual AC+ units can be connected in a point to multipoint or mesh configuration to allow interconnecting more than two sites.
With its password verification, MAC address authentication, SSID suppression and advanced WPA encryption, the system provides strong wireless data security.
If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.
The EZ-GO® Dual AC+ comes complete with all the electronics that are needed for a wireless network installation; including a powerful 802.11a/b/g/n/ac MIMO antenna, Stainless Steel hose clamp for 1-2” pole (or wall mounting), 48V PoE (Power over Ethernet) power inserter with auto-ranging 120/240VAC input, and one 3ft Ethernet patch cable. Customer to supply CAT5/6 cabling between the PoE inserter and the antenna.
Key Features
- High Power Electronics and Powerful MIMO Antenna
- True Plug and Play
- Dual Radio – 5GHz and 2.4GHz
- 64 and 128bit WEP, WPA Encryption
- Web-based configuration
- Power over Ethernet
- Layer 2 Transparent Bridge
- Multiple SSID
- Multiple SSID
- WiFi Analyzer
- External Status LEDs
- Operation up to 3 miles with good line of sight and up to 900 Mbps throughput
- No driver needed. Automatic peer to peer communications
- Provides 5GHz Backhaul and 2.4GHz Access Points
- Strong Wireless data security
- Remotely change device configuration or update firmware from anywhere on the network
- Up to 100meter (300’) cable from the PoE inserter to antenna
- Passes DHCP, VOIP Packets, Untagged VLAN Packets and supports multiple MAC addresses
- Up to 8 Virtual AP with custom SSID
- Supports VPN Pass Through
- Built in WiFi analyzer to show spectrum usage
- Indicates Sys Power, 2.4GHz and 5GHz Wireless
Technical Specification
- Data Rates:
- 5GHz: up to 900Mbps (80Mhz Channel)
- 5GHz: up to 450Mbps (40Mhz Channel)
- 5GHz: up to 225Mbps (20Mhz Channel)
- 2.4GHz: up to 300Mbps (802.11n / 40MHz)
- Standards: IEEE802.11a/b/g/n/ac, 802.3az, 802.3u
- Power Requirements:
- PoE Inserter: 100-240VAC 50/60Hz Input
- EZ-GO®: 48V 802.3af or 48V Passive PoE12VDC to Aux DC Connector Input
- Average Power Consumption: 6W
- Regulatory Certifications: FCC Part 15 / UL
- RF Frequency Bands:
- 2312 ~ 2483 MHz
- 5020 ~ 6100 MHz
- Modulation Technology:
- 802.11ac: OFDM 256QAM
- 802.11n: OFDM 64QAM
- 802.11b/g: DSSS
- Receive Sensitivity (Typical):
- 802.11ac: -86 dBm
- 802.11g/n: -88 dBm
- 802.11a: -90 dBm
- 801.11b: -94 dBm
- EVM – Error Vector Magnitude:
- 802.11ac: <-32 dB
- 802.11n: <-28 dB
- 802.11a/g: < -25 dB
- 802.11b: <-10 dB
- Transmit Power:25dBm 316mW Max
- Antenna:2.4GHz 12dBi MIMO ; 5GHz 14dBi MIMO Panel Antenna, 60deg Beamwidth
- Operation Mode – Bridge or Router:Access Point Mode, Repeater Mode (Client)
- Max Users: 128
- Interface: 10/100/1000Mbps Shielded RJ-45 Port x 2
- IP Configuration: Static or Auto configuration using DHCP Client
- Security: MAC Address Filtering, 128bit WEP/WPA encryption, Hide SSID in beacons
- Management Configuration: Web-based configuration (HTTP)
- Firmware Upgrade: Upgrade firmware via web browser
- Antenna Physical Dimensions (L x W x D): 315mm x 145mm x 80mm 12.4” x 5.7” x 3.1”
- Weight: 1.2 kg (2.6 lbs)
- Operating Temperature: -40°C to +55°C (-40°F to 131°F)
